Facebook YouTube Twitter LinkedIn
     
   

Precision LC II Ferroelectric Tester

 

Precision LCII Ferroelectric Test System

 
 

The Precision LCII is Radiant's answer to a growing need for affordable characterization equipment.  The Precision LCII is an ideal general-purpose tester with a broad test range for thin films and bulk ceramics.  The Precision LCII tester has a frequency rating of 5KHz at +/-200V built-in to the system.   Using up to 32,000 points with18-bit resolution from 2kHz out to 1/30th of a Hertz for capacitors ranging from square microns to square centimeters, the LC II enables high resolution characterization for bulk capacitors. The Precision LCII II is offered with a variety of internal amplifiers.  The Precision LCII is offered in a ±10V, 30V, 100V, 200V, and 500V built-in drive volt option.  The Precision LCII can be expanded to 10kV with the addition of a high voltage interface and amplifier. 

 Includes Vision Data Acquisition and Management System Software.

– A Library of 155 measurement, analysis, plotting, program control, and documentation tasks.

– An Editor to arrange multiple tasks together from the Library into a Test Definition.

– An Execution Engine to read and execute the Test Definition

– An amorphous database engine to Archive everything that happens in each Test Definition.

 

The Precision LCII executes hysteresis, pulse, leakage, IV, and CV (and many other tasks) measurements without changing sample connections.  With the addition of extra fixtures, the Precision LCII can measure pyroelectric properties, magnetoelectric properties, transistor characteristics, cryogenic properties, bulk and/or thin film piezoelectric properties.  

Vision dramatically increases the productivity of the researcher, reducing the time required to acquire data in an experiment.  Vision’s enhanced productivity directly reduces cost of test.  Vision dramatically increases the complexity of the research that may be accomplished by allowing researchers to combine different measurement tasks with environmental controls into an automated test procedure managed by programmable logic embedded with automated data collection, analysis and plotting tools. 

Materials Testers running under the Vision Materials RDP Operating System reduces Cost of Test by a factor greater than 10 over any other ferroelectric tester 

  


Precision LCII specifications include:
 
Tester Parameter

LC II

Voltage Range (built-in drive voltage)

±10V, ±30V, ±100V, ±200V or ±500V built-in

Voltage Range with an external amplifier and high voltage interface (HVI)

10KV

Number of ADC Bits

18

Minimum Charge Resolution

<10fC

Minimum Area Resolution (assuming 1 ADC bit = 1μC/cm2)

<1μ2

Maximum Charge Resolution

276μC

Maximum Area Resolution (assuming saturation polarization = 100μC/cm2)

2.76cm2

Maximum Charge Resolution with High Voltage Interface (HVI)

27.6mC

Maximum Area Resolution (assuming saturation polarization = 100μC/cm2) w/o HVI

>100cm2

Maximum Hysteresis Frequency

5KHz @ 10V

 

5KHz @ 30V

 

5KHz @ 100V

 

5KHz @ 200V

 

2KHz @ 500V

Minimum Hysteresis Frequency

0.03Hz

Minimum Pulse Width

50μs

Minimum Pulse Rise Time (5V)

40μs

Maximum Pulse Width

1s

Maximum Delay between Pulses

40ks

Internal Clock

25ns

Minimum Leakage Current (assuming max current integration period = 1 seconds)

1pA

Maximum Small Signal Cap Frequency

20KHz

Minimum Small Signal Cap Frequency

1Hz

Output Rise Time Control

103 scaling

Input Capacitance

-6fF

Electrometer Input All Test Frequencies for all test at any speed

Yes

* The minimum area resolution under actual test conditions depends upon the internal noise environment of the tester, the external noise environment, and the test jig parasitic capacitance.
*** Tester specifications are subject to change without notice.

 

Documentation

Precision LCII Brochure

Vision Data Acquisition and Management System

Request for Quotation


Accessories

     High Voltage Testing

     Piezoelectric Testing

     Thermal Testing 

     High Voltage Test
     Fixtures



 Support

 © 2016 - 2019   Radiant Technologies by AccuNet Web Services