Easy to set up, flexible, and affordable.
The Precision RT66C is perfect for a researcher looking for a flexible unit at an affordable price. The RT66C Test System has a hysteresis frequency rating of 1KHz. The RT66C is offered in a ± 200V built-in drive volt option. The RT66C can be expanded to 10kV with the addition of a 10kV High Voltage Interface and a High Voltage Amplifier.
±200V
Built-in drive voltage
1KHz
Maximum hysteresis frequency
14
Number of ADC bits
10kV
With an external amplifier and HVI
Precision RT66C (top) with a High Voltage Interface (bottom).
Specifications
Every parameter from the Precision RT66C specification table. Compare all four testers
Precision RT66C
Drive voltage
| Voltage Range (built-in drive voltage) | ±200V |
|---|---|
| Voltage Range with an external amplifier and high voltage interface (HVI) | 10KV |
Charge and area resolution
| Number of ADC Bits | 14 |
|---|---|
| Minimum Charge Resolution | 122fC |
| Minimum Area Resolution (assuming 1 ADC bit = 1μC/cm²) | 12.2μ² |
| Maximum Charge Resolution | 4.8μC |
| Maximum Area Resolution (assuming saturation polarization = 100μC/cm²) | 4.8mm² |
| Maximum Charge Resolution with High Voltage Interface (HVI) | 480μC |
| Maximum Area Resolution (assuming saturation polarization = 100μC/cm²) w/ HVI | 4.8cm² |
* The minimum area resolution under actual test conditions depends upon the internal noise environment of the tester, the external noise environment, and the test jig parasitic capacitance.
*** Tester specifications are subject to change without notice.
Hysteresis and pulse timing
| Maximum Hysteresis Frequency | 1KHz |
|---|---|
| Minimum Hysteresis Frequency | 1/8th Hz |
| Minimum Pulse Width | 500μs |
| Minimum Pulse Rise Time (5V) | 500μs |
| Maximum Pulse Width | 100ms |
| Maximum Delay between Pulses | 40ks |
| Internal Clock | 50μs |
| Output Rise Time Control | 2 settings |
Leakage, small signal, and input
| Minimum Leakage Current (assuming max current integration period = 1 seconds) | 10pA |
|---|---|
| Maximum Small Signal Cap Frequency | 2KHz |
| Minimum Small Signal Cap Frequency | 10Hz |
| Input Capacitance | 1pF |
| Electrometer Input All Test Frequencies for all test at any speed | Yes |
Price an RT66C for your lab.
Accessories for the RT66C
Tester accessories specifically used for the RT66C Ferroelectric Test System.
High Voltage Test Fixtures
The High Voltage Test Fixture, the Bulk Ceramic Piezoelectric Test Bundle, and the AutoCal 230°C Piezoelectric Thermal Test Chamber.
High Voltage Interface
Lets the Precision test system line run tests at voltages up to 10,000V, with four levels of safety.
High Voltage Amplifiers
External High Voltage Amplifiers, used with the High Voltage Interface. Quoted upon request.
Test Stations for Thin Films
RTI-30 and Simple Test Station probe stations for wafers and single die.
Vision Software is included with every Precision test system.
Radiant’s Precision Line of Test Systems are driven by Vision Software, with a library of over 150 measurement, analysis, plotting, program control, and documentation tasks.
Combine tests in one run
Chain Hysteresis, PUND, Fatigue, and Leakage in one Test Definition instead of running one test at a time.
Control the environment
Set temperature over GPIB, set the field of a Quantum Design superconducting magnet, and query an LCR meter within the test.
Let the logic decide
Branch tasks repeat steps until a value reaches your threshold; If/Then and Exit tasks skip steps or end the run based on a measured value.
Nothing gets lost
Every run is archived with its Test Definition, so any experiment can be recalled or reproduced.
Documentation and support
The RT66C brochure and the company brochure, plus the full knowledge base library.